Get matched with top doors installers or repairers in Philadelphia, PA

"Recently we hired Ardmore to replace the glass in 2 of our skylights and install a new storm door. Other than rain delays the skylights were installed in less than 2 hours as Ardmore sent 2 crews for the installation. They even came inside to vacuum any debris that might have fallen into the house during the installation. (5 out of 5). The installation of the storm doors was different. It took over 10 hours for 2 men to finish the installation which I felt was excessive and felt they didn't do the installation correctly. The difference between a good company and a better company is how well they fix a problem and to this point they are doing a better job. When I called to complain the scheduler immediately suggested they send out someone to inspect the work and within 3 days someone came out and fixed 2 out of the 3 problems and said someone would be calling me and ordering a replacement part to fix the 3rd problem"

"excellent work; carefully executed. Steve is very skilled all aspects of remodeling; dry wall, plumbing, painting, flooring, tiling and more."

"Excellent, no problems. My car was new the first year I used the service and there has never been any damage during the transports. The men picking up and delivering the car have always been pleasant and cooperative. Both Ely and Guy at United Transport has been highly responsive to my needs. I would highly recommend this company."

"This past weekend I had a bad experience. The short story is that an A. J. Perri technician diagnosed my furnace problem and wrote me an estimate for $1,600, parts and labor. It turns out my furnace had a different problem that required no parts and only 15 minutes of labor. Here are the details: This past Saturday my furnace stopped heating my home. I called A.J. Perri and they sent out a technician on Sunday morning. The tech ran some checks and concluded that my “inducer assembly” had to be replaced. Parts and installation would be $1,600. He said someone from the office would contact me on Monday and let me know when they could have the part. He also said that he couldn't be certain that there weren't other issues that wouldn't be found until the inducer was repaired. After the technician left I did some searching on the Internet. YouTube and Reddit were especially helpful. I discovered that the problem was that the condensate drain was clogged and water had backed up into the inducer assembly. The water prevented the pressure switches from detecting that the inducer was running and this prevented the furnace from starting. When I disconnected the condensate hose *2 quarts* of water drained out of the inducer assembly! This water was supposed to drain into a small pump unit on the floor that sends collected water to the sump. Over the years mold and algae had clogged the condensate trap and caused the backup. I disconnected all the hoses and removed the trap. I blew out the trap (making a mess) and confirmed that water would easily flow through it. I put it all back together and the furnace is working fine. The sad lesson here is that you can’t always rely on supposed experts. The good news is that the Internet can be your friend. Even more details: The original symptom was that the furnace would start up, the inducer motor would run for about 20 seconds and then it would shut off. This cycle would repeat every few minutes. Every few hours the furnace completed the startup cycle and then I’d get heat. Then it would stop heating for hours, and the indoor temperature would drop to the low 60s. What I learned from YouTube is that there are multiple stages for furnace startup. The inducer motor spins a cage that sucks in fresh air for combustion, and then pushes the hot gases through the heat exchanger and out the flue. Each stage in the startup has safety checks. The furnace will not ignite if the pressure sensors don’t detect that the inducer motor is working properly. Water is a byproduct of the combustion. It starts as a vapor but then condenses in the flue pipe and drains back to the inducer assembly, where it’s supposed to run through a hose to a pump that sends it over to my basement sump. The furnace is 14 years old. Apparently that’s long enough for mold and algae to clog the condensate trap and cause water to back up into the inducer. The 2 qts of water blocked the pressure sensor switches and so the furnace wouldn’t light. Final thoughts: For over 14 years I've had great experiences with A.J. Perri. They replaced my home’s original furnace and Air Conditioner units. They moved our outside A/C unit to the side of our house so we could have more quiet in the backyard. I had them come for periodic heating and A/C maintenance checkups. My impression is that they might cost a bit more, but they were reliable. I'm saddened that I need to post such a negative review."

"The OK: Towel bar had pulled out of the wall, that was reset and seems to be holding. Bedroom door that wasn't closing well was planed down at the top, I'm not really sure why I paid for that particular solution in retrospect, but was kind of buying into a grab bag, but fine. Kitchen counter caulked where it met the wall, again, not hard work, but fine. The Wasted Money: My front and back door sweeps seemed to have gaps you could see through to the outside and were coming apart. Since it's a pain to get under doors, I was good to pay a little extra for someone else to take that on. Replacement front sweep is already split again almost immediately. New back door sweep is still intact, but I guess as a "solution" the sill was raised and now there's a new gap there that the rain came through a few days ago. Also, under a section on my invoice somewhat brazenly labeled "custom carpentry" considering the end product, an estimate was given for replacing some of a wood rotted door frame as needed (even including "Reinstall brick molding as needed"). A lower piece of the frame was replaced with some solid wood, but it was seriously just cut out and hunk of wood thrown in. You can't miss it even at a glance, so we're at the barest definition of carpentry on that. But then on the top of the door, the wood was just dug out and replaced with layer after layer of putty. That's fine for a small job, but there was too much replacement needed here to not be replaced with actual wood. And the quote mentioning installing new wood and possibly brick molding was much more indicative of the work needed. The work performed still very much flexes at the touch and has started to visibly come apart again as any person would expect. And of course the shabby paint job done over it still leaves the "repair" very obvious as no effort was expended (or more likely wasn't in the capabilities of the "carpenter") to blend it with the frame. So a job that I very much paid to not be done, and that took a whole handful of visits even to be not completed. Also followed up with a plumbers referral from them and that worker also came up short as should be expected. Definitely would not transact with this company again."